• HUATEC GROUP CORPORATION
    بوب
    Astm E114-15 بوصة نوع 1018 معايرة اختبار كتلة الكربون الصلب ميني Iiw 2
  • HUATEC GROUP CORPORATION
    وليام
    Astm E114-15 بوصة نوع 1018 معايرة اختبار كتلة الكربون الصلب ميني Iiw 2
  • HUATEC GROUP CORPORATION
    توم
    Astm E114-15 بوصة نوع 1018 معايرة اختبار كتلة الكربون الصلب ميني Iiw 2
  • HUATEC GROUP CORPORATION
    ليو
    Astm E114-15 بوصة نوع 1018 معايرة اختبار كتلة الكربون الصلب ميني Iiw 2
اتصل شخص : Noah
رقم الهاتف : +8613911115555
واتس اب : +8613910983110

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE

مكان المنشأ بكين
اسم العلامة التجارية HUATEC
إصدار الشهادات ISO, CE, GOST
رقم الموديل HFD UL
الحد الأدنى لكمية قطعة واحدة
تفاصيل التغليف حزمة التصدير القياسية
وقت التسليم 1-4 أيام
شروط الدفع بـ (ت) ، (باي بال) ، (ويسترن يونيون)
القدرة على العرض 5000 قطعة شهريا

اتصل بي للحصول على عينات مجانية وكوبونات

واتس اب:0086 18588475571

(وي تشات): 0086 18588475571

سكايب: sales10@aixton.com

إذا كان لديك أي مخاوف، نحن نقدم المساعدة على الانترنت على مدار 24 ساعة.

x
تفاصيل المنتج
نطاق التردد 12.5 كيلو هرتز إلى 10 ميجا هرتز محول الاتصال حجم العنصر المتنوع
محول الوجه المحمي مع الفيلم أو الأحذية محول ذو عنصرين العنصر المزدوج
إسفين محدد الشكل مساعدة CID AOD COD المواد بلاستيك، ألومنيوم، سبيكة
إبراز

ultrasonic flaw detectors,ultrasonic flaw detection,digital ultrasonic flaw detector

,

ultrasonic flaw detection

,

digital ultrasonic flaw detector

اترك رسالة
منتوج وصف

 

Ultrasonic ndt equipment Ultrasonic Inspection Equipment Probe Transducer Phased Array Prob

 

1. Straight probe: single crystal p-wave straight probe double crystal p-wave straight probe

 

2. The Angle probe: single crystal shear Angle probe a1 < aL < a Ⅱ, twin shear Angle probe

 

Single-crystal p-wave oblique probe aL

AL is a climbing wave probe near a1. The longitudinal wave transmitted along the surface of the workpiece has the advantages of fast speed, high energy, long wavelength, deeper detection depth than the surface wave, and the requirement for the surface finish of the workpiece is higher than that of the surface wave (frequency 2.5mhz wavelength about 2.4mm).

 

3. Probe with curvature: circumferential curvature, radial curvature.

 

The circumferential curvature probe is suitable for the detection of axial defects in seamless steel tubes, straight welded tubes, tubular forgings and axial workpieces. When the diameter of the workpiece is less than 2000mm, the circumferential curvature of the probe shall be ground to ensure good coupling.

 

Radial curvature probe is suitable for the detection of radial defects in seamless steel pipe, butt weld of steel pipe, barrel forging, shaft workpiece, etc. When the workpiece diameter is less than 600mm, the radial curvature of the probe should be ground to ensure good coupling.

 

4. Focusing probe: point focusing line focusing.

 

5. Surface wave probe :(when the incident Angle of the longitudinal wave is greater than or equal to the second critical Angle, the transverse wave refraction Angle is equal to 90 to form a surface wave).

 

The transverse wave transmitted along the workpiece surface has a slow speed, low energy and short wavelength, and the detection depth is shallower than the crawling wave. Therefore, the requirements for the surface finish of the workpiece are stricter than the crawling wave.

 

Surface wave detection can only detect defects at a depth of two wavelengths from the surface of the workpiece. (frequency 2.5mhz wavelength about 1.3mm).

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 0

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 1

 

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 2

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 3

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 4

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 5

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 6

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 7

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 8

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 9Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 10

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 11

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 12

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 13

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 14

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 15